New Pullers and Grips
DCD Inner Duct Puller
DCD Standard Expanding Puller
DCD Deluxe Expanding Puller
Wire Mesh Pulling Grips (Heavy Duty)
Back to Tooling page. Contact us for ordering information.
Designed to install Polyethylene Ducting using a screw-in tapered buttress thread to grip the Inside diameter of the duct.
Also called the Screw-in or Carrot Pulling Eye, this is one of the most commonly used types of pulling device. It has a simple, inexpensive, one-piece construction with two flutes designed to actually cut a thread in the bore of the duct as it is screwed in. Virtually impossible to pull out, this product is hard to beat.
| Description |
Fits |
Price |
| DCD Inner Duct Puller (3/4") |
0.72 to 0.93 ID |
$35.00 USD |
| DCD Inner Duct Puller (1") |
0.94 to 1.15 ID |
$37.50 USD |
| DCD Inner Duct Puller (1-1/4") |
1.26 to 1.44 ID |
$42.00 USD |
| DCD Inner Duct Puller (1-1/2") |
1.48 to 1.66 ID |
$45.00 USD |
| DCD Inner Duct Puller (2") |
1.91 to 2.08 ID |
$57.50 USD |
| Driving Tool |
All Sizes |
$49.00 USD |
Designed to grip polyethylene ducting using expanding jaws to grip the inside wall of the duct. This causes the pulling load to be spread around the circumference of the duct and allows a maximum load to be applied without damage to the ducting.
On thin wall ducting, it is recommended that an outer Duct Sleeve be used to prevent the duct from stretching during installation.
Use of a duct plugger will help prevent mud and slurry from entering past the puller into the ducting.
| Description |
Fits |
Price |
| DCD Standard Expanding Puller (1-1/4") |
1.29 to 1.50 ID |
$125 USD |
| DCD Standard Expanding Puller (1-1/2") |
1.60 to 1.68 ID |
$150 USD |
| DCD Standard Expanding Puller (2") |
1.88 to 2.12 ID |
$195 USD |
| DCD Standard Expanding Puller (2-1/2") |
2.25 to 2.50 ID |
$265 USD |
| DCD Standard Expanding Puller (3") |
2.75 to 3.06 ID |
$310 USD |
| DCD Standard Expanding Puller (4") |
3.50 to 4.06 ID |
$375 USD |
| DCD Standard Expanding Puller (5") |
4.50 to 5.00 ID |
$555 USD |
| DCD Standard Expanding Puller (6") |
5.44 to 6.12 ID |
$675 USD |
| DCD Standard Expanding Puller (8") |
6.44 to 7.87 ID |
$850 USD |
Designed to install polyethylene ducting using expanding jaws to grip the inside diameter of the duct while the outside diameter is prevented from stretching by a permanent outer sleeve on the puller. The outer sleeve also provides a complete watertight seal around the ducting preventing any fluids or contaminants from entering either the duct or the pulling eye.
Also known as DUB-Wise Pullers, these duct pullers are installed quickly and easily and require no special tooling. A new tooth profile makes removal much easier than the earlier models.
| Description |
Fits |
Price |
| DCD Deluxe Expanding Puller (1-1/4") |
1.25 to 1.50 ID |
$145 USD |
| DCD Deluxe Expanding Puller (1-1/2") |
1.44 to 1.68 ID |
$165 USD |
| DCD Deluxe Expanding Puller (2") |
1.82 to 2.37 ID |
$215 USD |
| DCD Deluxe Expanding Puller (2-1/2") |
2.37 to 2.56 ID |
$270 USD |
| DCD Deluxe Expanding Puller (3") |
2.69 to 3.06 ID |
$315 USD |
| DCD Deluxe Expanding Puller (4") |
3.44 to 4.25 ID |
$415 USD |
| DCD Deluxe Expanding Puller (5") |
4.32 to 5.12 ID |
$575 USD |
| DCD Deluxe Expanding Puller (6") |
5.07 to 6.06 ID |
$675 USD |
Manufactured of Hi-Fatigue plastic coated Aircraft Strand steel cable in various weave designs. Recommended wherever high strength and small size are required. Patented pulling eye is flexible and stress relieving.
| Description |
Fits |
Price |
| DCD Wire Mesh Pulling Grip (0.75" to 1.12", Double Weave, 24"L) |
6,700 lb |
$68 USD |
| DCD Wire Mesh Pulling Grip (1.18" to 1.49", Double Weave, 24"L) |
10,000 lb |
$75 USD |
| DCD Wire Mesh Pulling Grip (1.50" to 1.99", Double Weave, 24"L) |
16,400 lb |
$85 USD |
| DCD Wire Mesh Pulling Grip (2.00" to 2.49", Triple Weave, 24"L) |
18,500 lb |
$112 USD |
| DCD Wire Mesh Pulling Grip (2.50" to 2.99", Triple Weave, 36"L) |
24,500 lb |
$130 USD |
| DCD Wire Mesh Pulling Grip (3.00" to 3.74", Triple Weave, 36"L) |
24,500 lb |
$145 USD |
| DCD Wire Mesh Pulling Grip (3.75" to 4.24", Triple Weave, 48"L) |
31,000 lb |
$160 USD |
| DCD Wire Mesh Pulling Grip (3.75" to 4.99", Triple Weave, 48"L) |
31,000 lb |
$168 USD |
|